Microcantilever beams were fabricated through a microelectromechanical system fabrication process; this process was improved by using etched slots. The actual mechanical properties of the cantilever beams can be estimated using a nanoindenter. Various cantilever beam widths and length-to-width ratios were used for evaluation. Five structures of cantilever beams were fabricated and compared. ANSYS software was used to simulate cantilever beam deflections. The etched slots increased the cantilever beam deflections, and the increase in deflection was apparent when the etched slot was located near the base of the beams. Type 4 was a cantilever beam with an etched slot of length L/2 near the base of the beam. The area of the etched slots of type 4 was larger, and the etched slot of type 4 was near the base of the cantilever beam. Type 4 had the shortest etching time, highest fabrication success rate, and greatest deflection. The difference between the measured and simulated (without parameter modification) deflections could exceed 10%. Modifying the force acting point and Young's modulus in the simulations reduced the difference between the measured and simulated deflections to 0.5%. This demonstrates that actual experimental conditions considerably influence simulation results, and this can be beneficial to subsequent studies.

References

1. 1)
  - 28. Barnes, J.R., Stephenson, R.J., Welland, M.E., et al: ‘Photothermal spectroscopy with femtojoule sensitivity using a micromechanical device’, Nature, 1994, 372, pp. 79–81 (doi: 10.1038/372079a0).
2. 2)
  - 33. Ilic, B., Yang, Y., Aubin, K., et al: ‘Enumeration of DNA molecules bound to a nanomechanical oscillator’, Nanoletters, 2005, 5, pp. 925–929 (doi: 10.1021/nl050456k).
3. 3)
  - 23. Tanguy, M., Bourmaud, A., Baley, C.: ‘Plant cell walls to reinforce composite materials: relationship between nanoindentation and tensile modulus’, Mater. Lett., 2016, 167, pp. 161–164 (doi: 10.1016/j.matlet.2015.12.167).
4. 4)
  - [5]. Zhang, Q., Gao, S., Min, J., et al: ‘Graded viscoelastic behavior of human enamel by nanoindentation’, Mater. Lett., 2016, 179, pp. 126–129 (doi: 10.1016/j.matlet.2016.05.034).
5. 5)
  - 18. Charitidis, C.A., Skarmoutsou, A., Tsetsekou, A., et al: ‘Nanomechanical properties of hydroxyapatite (HAP) with DAB dendrimers (poly-propylene imine) coatings onto titanium surfaces’, Mater. Sci. Eng., B, 2013, 178, pp. 391–399 (doi: 10.1016/j.mseb.2013.01.002).
6. 6)
  - 30. Arakawa, E.T., Lavrik, N.V., Rajiv, S., et al: ‘Detection and differentiation of biological species using microcalorimetric spectroscopy’, Ultramicroscopy, 2003, 97, pp. 459–465 (doi: 10.1016/S0304-3991(03)00074-3).
7. 7)
  - 12. Zhang, Z., Zhang, N., Ma, G., et al: ‘Characterization of microstructural stability for nanotwinned mercury cadmium telluride under cyclic nanoindentations’, Scr. Mater., 2013, 69, pp. 299–302 (doi: 10.1016/j.scriptamat.2013.04.024).
8. 8)
  - 13. Concustell, A., Mattern, N., Wendrock, H., et al: ‘Mechanical properties of a two-phase amorphous Ni–Nb–Y alloy studied by nanoindentation’, Scr. Mater., 2007, 56, pp. 85–88 (doi: 10.1016/j.scriptamat.2006.09.026).
9. 9)
  - 26. Petersen, K.E.: ‘Dynamic micromechanics on silicon: techniques and devices’, IEEE Trans. Electron Devices, 1978, 25, pp. 1241–1250 (doi: 10.1109/T-ED.1978.19259).
10. 10)
  - 4. Snow, D., Weeks, L.B., Kim, D.J., et al: ‘Static deflection measurements of cantilever arrays reveal polymer film expansion and contraction’, J. Colloid Interface Sci., 2007, 316, pp. 687–693 (doi: 10.1016/j.jcis.2007.08.050).
11. 11)
  - 29. Li, X.D., Bhushan, B.: ‘A review of nanoindentation continuous stiffness measurement technique and its applications’, Mater. Charact., 2002, 48, pp. 11–36 (doi: 10.1016/S1044-5803(02)00192-4).
12. 12)
  - 14. Broitman, E., Tengdelius, L., Hangen, U.D., et al: ‘High-temperature nanoindentation of epitaxial ZrB2 thin films’, Scr. Mater., 2016, 124, pp. 117–120 (doi: 10.1016/j.scriptamat.2016.06.033).
13. 13)
  - 10. Li, M.C., Jiang, M.Q., Jiang, F., et al: ‘Testing effects on hardness of a Zr-based metallic glass under nanoindentation’, Scr. Mater., 2017, 138, pp. 120–123 (doi: 10.1016/j.scriptamat.2017.05.046).
14. 14)
  - 2. Zhuang, F.K., Tu, S.T., Zhou, G.Y., et al: ‘A small cantilever beam test for determination of creep properties of materials’, Fatigue Fract. Eng. Mater. Struct., 2015, 38, pp. 257–267 (doi: 10.1111/ffe.12225).
15. 15)
  - 27. Roylance, L.M., Angell, J.B.: ‘A batch-fabricated silicon accelerometer’, IEEE Trans. Electron Devices, 1979, 26, pp. 1911–1917 (doi: 10.1109/T-ED.1979.19795).
16. 16)
  - 17. Hong, Y., Zhou, C., Zheng, Y., et al: ‘Hydrogen effect on the deformation evolution process in situ detected by nanoindentation continuous stiffness measurement’, Mater. Charact., 2017, 127, pp. 35–40 (doi: 10.1016/j.matchar.2017.02.012).
17. 17)
  - 31. Battison, F.M., Ramseyer, J.P., Lang, H.P., et al: ‘A chemical sensor based on a microfabricated cantilever array with simultaneous resonance-frequency and bending readout’, Sens. Actuators B, 2001, 77, pp. 122–131 (doi: 10.1016/S0925-4005(01)00683-9).
18. 18)
  - 20. Su, J.F., Wang, X.Y., Dong, H.: ‘Micromechanical properties of melamine–formaldehyde microcapsules micromechanical properties of melamine–formaldehyde microcapsules’, Mater. Lett., 2012, 89, pp. 1–4 (doi: 10.1016/j.matlet.2012.08.072).
19. 19)
  - 35. Hibbeler, R.C.: ‘Mechanics of materials’ (Pearson Education, UK, 2016, 10th edn.).
20. 20)
  - 37. Wang, P.C., Lee, J.W., Yang, T.C., et al: ‘Effects of silicon contents on the characteristics of Zr-Ti-Si-W thin film metallic glasses’, Thin Solid Films, 2016, 618, pp. 28–35 (doi: 10.1016/j.tsf.2016.03.043).
21. 21)
  - 16. Moniruzzaman, M., Zioupos, P., Fernando, G.F.: ‘Investigation of reversible photo-mechanical properties of azobenzene-based polymer films by nanoindentation’, Scr. Mater., 2006, 54, pp. 257–261 (doi: 10.1016/j.scriptamat.2005.09.025).
22. 22)
  - 32. Lee, J.H., Hwang, K.S., Park, J., et al: ‘Immunoassay of prostate-specific antigen (PSA) using resonant frequency shift of piezoelectric nanomechanical microcantilever’, Biosens. Bioelectron., 2005, 20, pp. 2157–2162 (doi: 10.1016/j.bios.2004.09.024).
23. 23)
  - 7. Zhou, L., Giri, A., Cho, K., et al: ‘Mechanical anomaly observed in Ni-Mn-Ga alloys by nanoindentation’, Acta Mater., 2016, 118, pp. 54–63 (doi: 10.1016/j.actamat.2016.07.029).
24. 24)
  - 24. Singh, S.S., Jansen, M.A., Franz, N., et al: ‘Microstructure and nanoindentation of the rostrum of Curculio longinasus Chittenden, 1927 (Coleoptera: Curculionidae)’, Mater. Charact., 2016, 118, pp. 206–211 (doi: 10.1016/j.matchar.2016.05.022).
25. 25)
  - 11. Liang, W., Ning, Z., Dang, Z., et al: ‘Plastic deformation behaviors of Ni- and Zr-based bulk metallic glasses subjected to nanoindentation’, Mater. Charact., 2013, 86, pp. 290–295 (doi: 10.1016/j.matchar.2013.10.014).
26. 26)
  - 21. Al-Halhouli, A.T., Kampen, I., Krah, T., et al: ‘Nanoindentation testing of SU-8 photoresist mechanical properties’, Microelectron. Eng., 2008, 85, pp. 942–944 (doi: 10.1016/j.mee.2008.01.033).
27. 27)
  - 9. He, B.B., Huang, M.X., Liang, Z.Y., et al: ‘Nanoindentation investigation on the mechanical stability of individual austenite grains in a medium-Mn transformation-induced plasticity steel’, Scr. Mater., 2013, 69, pp. 215–218 (doi: 10.1016/j.scriptamat.2013.03.030).
28. 28)
  - 6. Komeili, M., Menon, C.: ‘Modelling a micro-cantilever vibrating in vacuum, gas or liquid under thermal base excitation’, Mech. Res. Commun., 2016, 73, pp. 39–46 (doi: 10.1016/j.mechrescom.2016.01.009).
29. 29)
  - 29. Oden, P.I., Chen, G.Y., Steele, R.A., et al: ‘Viscous drag measurements utilizing microfabricated cantilevers’, Appl. Phys. Lett., 1996, 68, pp. 3814–3816 (doi: 10.1063/1.116626).
30. 30)
  - 5. Arya, S., Khan, S., Lehana, P.: ‘Design and fabrication of electrostatic micro-cantilever array as audible frequency generator’, J. Electrost., 2015, 76, pp. 145–151 (doi: 10.1016/j.elstat.2015.05.015).
31. 31)
  - 28. Oliver, W.C., Pharr, G.M.: ‘An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments’, J. Mater. Res., 1992, 7, pp. 1564–1583 (doi: 10.1557/JMR.1992.1564).
32. 32)
  - 15. Wang, Y., Cheng, Y.: ‘A nanoindentation study of the viscoplastic behavior of pure lithium’, Scr. Mater., 2017, 130, pp. 191–195 (doi: 10.1016/j.scriptamat.2016.12.006).
33. 33)
  - 3. Hopcroft, M., Kramer, T., Kim, G., et al: ‘Micromechanical testing of SU-8 cantilevers’, Fatigue Fract. Eng. Mater. Struct., 2005, 28, pp. 735–742 (doi: 10.1111/j.1460-2695.2005.00873.x).
34. 34)
  - 25. Kim, Y.Y.: ‘Young's modulus measurement of a silicon nitride thin-film using an ultrasonically actuated microcantilever’, Measurement, 2018, 115, pp. 133–138 (doi: 10.1016/j.measurement.2017.10.029).
35. 35)
  - 8. Hu, Z., Shrestha, M., Fan, Q.H.: ‘Nanomechanical characterization of porous anodic aluminum oxide films by nanoindentation’, Thin Solid Films, 2016, 598, pp. 131–140 (doi: 10.1016/j.tsf.2015.11.073).
36. 36)
  - 1. Liu, J., Zhu, X., Li, X., et al: ‘Abnormal bending of micro-cantilever plate induced by a droplet’, Acta Mech. Solida Sin., 2010, 23, pp. 428–436 (doi: 10.1016/S0894-9166(10)60045-6).
37. 37)
  - 34. Wu, G.H., Datar, R.H., Hansen, K.M., et al: ‘Bioassay of prostate-specific antigen (PSA) using microcantilever’, Nat. Biotechnol., 2001, 19, pp. 856–860 (doi: 10.1038/nbt0901-856).

Enhancement of microcantilever beams fabrication and determination of their mechanical properties using nanoindentation

References

Related content