Since the proposing of capacitive micromachined ultrasonic transducer by Khuri Yakub group in 1994 that this kind of transducer occupying the advantages of wide bandwidth, impedance matching well with the propagation medium especially in fluid and air and high sensitivity, has shown a great potential for wide ranges of applications. This Letter reports kind of micro-electro-mechanical systems (MEMS) capacitive ultrasonic transducer with the novel cavities embedded in the device layer of silicon on insulator wafer bonded with a glass substrate. The optimum geometric dimensions are confirmed by both mechanical vibrating of the membrane and the electrical characteristics analysis. Finite-element analysis is adopted to determine the operation mode. The safety and reliability of the proposed device is ensured by the obtained deflections and equivalent stress under operation/collapse voltage. The bottom electrodes of the proposed transducer are fabricated on the top surface of the glass substrate. The parallel parasitic capacitance is reduced, thus improving the electromechanical coupling coefficient. The test results show that the electromechanical coupling coefficient is 69.65%, which demonstrates that this proposed MEMS capacitive ultrasonic transducer structure can enhance the performance significantly.

References

1. 1)
  - 10. Wong, S., Kupnik, M., Zhuang, X., et al: ‘Evaluation of wafer bonded CMUTs with rectangular membranes featuring high fill factor’, IEEE Trans. Ultrason. Ferroelectr. Freq. Control, 2008, 55, pp. 2053–2065 (doi: 10.1109/TUFFC.897).
2. 2)
  - 12. Bellaredj, M., Bourbon, G., Walter, V., et al: ‘Anodic bonding using SOI wafer for fabrication of capacitive micromachined ultrasonic transducers’, J. Micromech. Microeng., 2014, 24, p. 12 (doi: 10.1088/0960-1317/24/2/025009).
3. 3)
  - 7. Johnson, J., Oralkan, Ö., Demirci, U., et al: ‘Medical imaging using capacitive micromachined ultrasonic transducer arrays’, Ultrasonics, 2002, 40, p. 6 (doi: 10.1016/S0041-624X(02)00161-0).
4. 4)
  - 1. Haller, M.I., Khuri-Yakub, B.T.: ‘A surface micromachined electrostatic ultrasonic air transducer’, Ultrason. Symp., 1994, 2, p. 4.
5. 5)
  - 6. Soh, H.T., Ladabaum, I., Atalar, A., et al: ‘Silicon micromachined ultrasonic immersion transducers’, Appl. Phys. Lett., 1996, 69, p. 3 (doi: 10.1063/1.117185).
6. 6)
  - 4. Haller, M.I., Khuri-Yakub, B.T.: ‘A surface micromachined electrostatic ultrasonic air transducer’, IEEE Trans. Ultrason. Ferroelectr. Freq. Control, 1996, 43, p. 6 (doi: 10.1109/58.484456).
7. 7)
  - 8. Cianci, E., Visigalli, L., Foglietti, V., et al: ‘Improvements towards a reliable fabrication process for cMUT’, Microelectron. Eng., 2003, 67–68, pp. 602–608 (doi: 10.1016/S0167-9317(03)00120-5).
8. 8)
  - 15. Hunt, F.V.: ‘The analysis of transduction, and its historical background’ (Harvard University Press, Cambridge, MA, 1954).
9. 9)
  - 13. Yaralioglu, G.G., Ergun, A.S., Bayram, B., et al: ‘Calculation and measurement of electromechanical coupling coefficient of capacitive micromachined ultrasonic transducers’, IEEE Trans. Ultrason. Ferroelectr. Freq. Control, 2003, 50, p. 8 (doi: 10.1109/TUFFC.2003.1197968).
10. 10)
  - 14. Senturia, S.D.: ‘Microsystems design’ (Kluwer Academic, Pub, Boston, 2001).
11. 11)
  - 5. Spoliansky, D., Ladabaum, I., Khuri-Yakub, B.T.: ‘Micromachined ultrasonic air-transducers (MUTs)’, Microelectron. Eng., 1996, 30, p. 4 (doi: 10.1016/0167-9317(95)00303-7).
12. 12)
  - 3. Hansen, S.T., Ergun, A.S., Liou, W., et al: ‘Wideband micromachined capacitive microphones with radio frequency detection’, J. Acoust. Soc. Am., 2004, 116, p. 828 (doi: 10.1121/1.1771617).
13. 13)
  - 1. Khuri-Yakub, B.T., Oralkan, O.: ‘Capacitive micromachined ultrasound transducers for medical imaging and therapy’, J. Micromech. Microeng., 2011, 21, (05), p. 54004, (doi: 10.1088/0960-1317/21/5/054004).
14. 14)
  - 11. Zhuang, X., Lin, D.-S., Oralkan, Ö., et al: ‘Fabrication of flexible transducer arrays with through-wafer electrical interconnects based on trench refilling with PDMS’, J. Microelectromech. Syst., 2008, 17, p. 6.
15. 15)
  - 9. Huang, Y., Ergun, A.S., Haeggstrom, E., et al: ‘Fabricating capacitive micromachined ultrasonic transducers with wafer-bonding technology’, J. Microelectromech. Syst., 2003, 12, p. 10.

Micro-electro-mechanical systems capacitive ultrasonic transducer with a higher electromechanical coupling coefficient

References

Related content