To decrease the injury caused by an accidental collision between the hydraulic manipulator and human, a hydraulic rotating angle self-servo compliant robot driver joint is designed. Based on this joint, a variable stiffness passive servo-hydraulic rotary joint is improved. The passive follow-up characteristics of the improved servo-hydraulic rotary joint enable it to enter the low stiffness mode by itself when it encounters collisions beyond the force limit. Combining this characteristic, the research method of the hydraulic mechanical arm flexible configuration is proposed. Firstly, the joint motion mode is defined by the Euler angle, and a variety of configurations conforming to the motion characteristics of the manipulator are determined. Then, the virtual prototype and collision environment are built, and the dynamic characteristics of the end effector of the arm under high and low stiffness are measured. The results show that the flexible configurations with passive follow-up characteristics can significantly suppress the collision force. Finally, the visual method is employed to solve, draw, and compare the workspace of the selected compliant configuration, to obtain the optimal compliant configuration with both flexibility and motion, which provides theoretical guidance for the subsequent design of the compliant manipulator.

References

1. 1)
  - 15. Zhao, J., Song, C., Du, B.: ‘Research on ergonomic mechanical arm configuration based on ergonomics’, J. Mech. Eng., 2013, 49, (11), pp. 16–21.
2. 2)
  - 5. Zhao, H.F., Zhang, X.L.: ‘Design and control of lightweight and flexible manipulators’, J. Beijing Jiaotong Univ., 2018, 42, (1), pp. 113–119.
3. 3)
  - 11. Yeo, S.H., Yang, G., Lim, W.B.: ‘Design and analysis of cable-driven manipulators with variable stiffness’, Mech. Mach. Theory, 2013, 69, (Complete), pp. 230–244.
4. 4)
  - 1. Park, J., Song, J., Haddadin, S.: ‘Collision analysis and safety evaluation using a collision model for the frontal robot–human impact’, Robotica, 2015, 33, (7), pp. 1536–1550.
5. 5)
  - 9. Mathijssen, G., Schultz, J., Vanderborght, B., et al: ‘A muscle-like recruitment actuator with modular redundant actuation units for soft robotics’, Robot. Auton. Syst., 2015, 74, (PA), pp. 40–50.
6. 6)
  - 6. Shi, Y.L., Zhang, X.J., Zhang, M.L.: ‘Design and analysis of active-passive composite variable stiffness flexible joints’, J. Mech. Eng., 2018, 54, (3), pp. 55–62.
7. 7)
  - 10. Yoo, J., Hyun, M.W., Choi, J.H., et al: ‘Optimal design of a variable stiffness joint in a robot manipulator using the response surface method’, J. Mech. Sci. Technol., 2009, 23, (8), pp. 2236–2243.
8. 8)
  - 4. Meng, D.S., Wang, X.Q., Liang, B., et al: ‘Optimization of the safety configuration of flexible joint manipulator based on head collision equivalent model’, Robot, 2017, 39, (4), pp. 523–531.
9. 9)
  - 16. He, Y., Luo, J., Zhang, Y., et al: ‘Synthesis and research of anthropomorphic manipulator configuration based on ergonomics’, Mach. Manuf., 2014, 52, (11), pp. 28–31.
10. 10)
  - 19. Xing, T.: ‘Kinematics and dynamics analysis and simulation of loading and unloading manipulators’. Master thesis, Qingdao University of Science and Technology, 2012.
11. 11)
  - 7. Choi, J., Hong, S., Lee, W., et al: ‘A robot joint with variable stiffness using leaf springs’, IEEE Trans. Robot., 2011, 27, (2), pp. 229–238.
12. 12)
  - 3. Zhang, X.L., Gu, X.X., Zhao, H.F., et al: ‘Design of a compliant mechanical arm based on a series of elastic actuators’, Robot, 2016, 38, (4), pp. 385–394.
13. 13)
  - 20. Fu, X., Han, S., Zhang, D., et al: ‘Kinematics analysis and trajectory planning of packaging sorting manipulator based on D-H method’, Packag. Food Mach., 2018, 36, (5), p. 46+52–55.
14. 14)
  - 12. Xiang, C., Giannaccini, M.E., Theodoridis, T., et al: ‘Variable stiffness Mckibben muscles with hydraulic and pneumatic operating modes’, Adv. Robot., 2016, 30, (13), pp. 889–899.
15. 15)
  - 2. Tian, Y., Wang, H.G., Pan, X.A.: ‘Configuration analysis of a 6R manipulator based on an improved performance index’. Int. Conf. on Robotics & Biomimetics, Macao, People's Republic of China, 2017.
16. 16)
  - 17. Smith, T., Jones, M.: ‘The title of the paper’, IET Syst. Biol., 2007, 1, (2), pp. 1–7.
17. 17)
  - 13. Fu, X., Wang, W., Wang, L., et al: ‘Analysis and study on dynamical characteristics of variable stiffness joint actuator’, Robot, 2017, 39, (4), pp. 466–473.
18. 18)
  - 18. Zhou, W., Chen, F., Shen, J., et al: ‘Kinematics simulation of four-degree-of-freedom manipulator based on MATLAB’, Mach. Manuf. Autom., 2016, 45, (1), pp. 115–119.
19. 19)
  - 8. Hyun, D., Yang, H.S., Park, J., et al: ‘Variable stiffness mechanism for human-friendly robots’, Mech. Mach. Theory, 2010, 45, (6), pp. 880–897.
20. 20)
  - 14. Ryusuke, M., Hiroyuki, N., Gen, E., et al: ‘A proposal of a new rotational-compliant joint with oil-hydraulic McKibben artificial muscles’, Adv. Robot., 2018, 32, (9), pp. 511–523.

Research on compliant configuration of hydraulic manipulator with passive following characteristic

References

Related content