http://iet.metastore.ingenta.com
1887

access icon openaccess Research on detection technology of wire clamp on overhead lines

  • HTML
    40.5205078125Kb
  • XML
    38.626953125Kb
  • PDF
    1.4536657333374023MB
Loading full text...

Full text loading...

/deliver/fulltext/10.1049/joe.2018.8430/JOE.2018.8430.html;jsessionid=1cb23hsv9gp1a.x-iet-live-01?itemId=%2fcontent%2fjournals%2f10.1049%2fjoe.2018.8430&mimeType=html&fmt=ahah

References

    1. 1)
      • 1. Wu, G., Yuan, Z.: ‘Pressure contact technique for strain clamps used for conductors with large-cross section’, Electr. Power Constr., 2010, 31, (5), pp. 126129.
    2. 2)
      • 2. Feng, A., Jin, R.: ‘Influencing factors of holding force for conductor crimping’, Electr. Power Constr., 2011, 32, (11), pp. 8588.
    3. 3)
      • 3. Hu, J., Liu, C., Ouyang, K., et al: ‘Analysis on cracking failure of strain clamp on 500 kV DC transmission line’, Electr. Power Constr., 2012, 33, (7), pp. 8285.
    4. 4)
      • 4. Han, G., Wu, Z., Wan, S., et al: ‘The detection research of high voltage transmission line internal defects based on X-ray digital radiography’, Sci. Technol. Eng., 2015, 15, (3), pp. 227230.
    5. 5)
      • 5. Liu, L., Zou, W., Li, P.: ‘Analysis on 220 kV line clamp failure’, Heat Treatment, 2015, 30, (3), pp. 4852.
    6. 6)
      • 6. Dou, H., Wu, H., Lin, J., et al: ‘Fracture rule of conductor in clamp by abnormal temperature rising due to strands damage’, Eng. J. Wuhan Univ., 2013, 46, (5), pp. 664668.
    7. 7)
      • 7. Peng, X.: ‘Causation analysis by test and detection on break fault of 220 kV overhead transmission line’, High Volt. Appar., 2011, 11, (2), pp. 354366.
    8. 8)
      • 8. Crinon, E., Evans, J.T.: ‘The effect of surface roughness, oxide film thickness and interfacial sliding on the electrical contact resistance of aluminium’, Mater. Sci. Eng., A, 1998, 242, (1–2), pp. 121128.
    9. 9)
      • 9. Callen, B.W., Johnson, B., King, P., et al: ‘Environmental degradation of utility power connectors in a harsh environment’, IEEE Trans. Compon. Packag. Technol., 2000, 23, (2), pp. 261270.
    10. 10)
      • 10. Cui, M., Jia, C., Wang, S., et al: ‘Thermal image characteristic based on poor contact between conductor and clap’, Jilin Electr. Power, 2013, 41, (6), pp. 3638.
    11. 11)
      • 11. Wang, Z.: ‘Analysis on breakage causes of steel-cored aluminum strands in strained tube’, Electr. Power Constr., 2005, 26, (4), pp. 3538.
    12. 12)
      • 12. Zhan, M.: ‘Running and residual life management for strain clamp of overhead line’. PhD thesis, Hefei University of Technology, 2005.
    13. 13)
      • 13. Ying, W., Hu, X., Huang, X.: ‘Analysis of verification for splicing size and mechanical load of overhead conductor strain clamp’, Zhejiang Electr. Power, 2010, 81, (7), pp. 1416.
    14. 14)
      • 14. Lu, Z., Liu, G., Wang, M., et al: ‘Research on the relationship between steel core and tubes of clamp crimped size and tensile capacity of overhead wires based on X-ray’, Sci. Technol. Eng., 2015, 15, (5), pp. 243247.
    15. 15)
      • 15. Zhu, C., Li, X., Wu, H., et al: ‘Failure caused by malposition defects and failure simulation of electric transmission line compression fittings’, Corros. Prot., 2015, 36, (4), pp. 373377.
    16. 16)
      • 16. GB/T 2314-2008: ‘Fittings general technical requirements’, 2008.
http://iet.metastore.ingenta.com/content/journals/10.1049/joe.2018.8430
Loading

Related content

content/journals/10.1049/joe.2018.8430
pub_keyword,iet_inspecKeyword,pub_concept
6
6
Loading
This is a required field
Please enter a valid email address