Lightweight stator structure for a large diameter direct-drive permanent magnet synchronous generator intended for wind turbines

R. Scott Semken; Charles Nutakor; Aki Mikkola; Yulia Alexandrova

Lightweight stator structure for a large diameter direct-drive permanent magnet synchronous generator intended for wind turbines

View Fulltext

Author(s): R. Scott Semken ¹ ; Charles Nutakor ¹ ; Aki Mikkola ¹ ; Yulia Alexandrova ²
- Affiliations: 1: Department of Mechanical Engineering, Lappeenranta University of Technology, Lappeenranta, Finland;
  2: Department of Electrical Engineering, Lappeenranta University of Technology, Lappeenranta, Finland
Source: Volume 9, Issue 7, September 2015, p. 711 – 719
DOI: 10.1049/iet-rpg.2014.0391 , Print ISSN 1752-1416, Online ISSN 1752-1424

« Previous Article
Table of contents
Next Article »

Received 14/11/2014, Accepted 16/02/2015, Revised 22/01/2015, Published 07/04/2015

A concept has been developed for a novel lightweight wheel structure intended for rotor and stator use in direct-drive wind turbine generators. It uses a slanted spoke and rim architecture to provide maximum static structural performance with minimum weight. A unique attribute of the structure is its use of layered sheet steel elements to form the spokes and rim. Friction between layers establishes structural integrity. The interaction between layers and the resulting increase in damping normal to the stack offers improved dynamic performance. A static structural analysis of a full-scale stator wheel structure for an 8 MW permanent magnet machine demonstrates the structural effectiveness of the architecture. To understand vibration characteristics of the lightweight wheel structure, a quarter-scale prototype was built and an experimental modal analysis was carried out to measure actual radial vibration responses. This data was used to verify a numerical model, and there was good agreement between measured and predicted behaviours. Finally, a modal analysis was carried out for the full-scale stator wheel structure. The dynamic performance of the wheel is acceptable for the stator of the 8 MW direct-drive permanent magnet synchronous generator embodiment.

References

1. 1)
  - 14. Versteegh, C.J.A., Hassan, G.: ‘Design of the Zephyros Z72 wind turbine with emphasis on the direct drive PM generator’. Nordic Workshop on Power and Industrial Electronics (NORPIE), Trondheim, 2004.
2. 2)
  - 1. Bang, D., Polinder, H., Shrestha, G., et al: ‘Review of generator systems for direct-drive wind turbines’. European Wind Energy Conf. and Exhibition, Belgium, 2008, pp. 1–11.
3. 3)
  - M.A. Mueller , A.S. McDonald . A lightweight low-speed permanent magnet electrical generator for direct-drive wind turbines. Wind Energy , 768 - 780
4. 4)
  - 7. Thomas, V.T.: Der Wettbewerb bei getriebelosen Windenergieanlagen ist eröffnet. http://www.enercon.de/p/downloads/WB-0408-en.pdf. VDI Nachrichten, Issue 04, 01/2011.
5. 5)
  - A.S. McDonald , M.A. Mueller , H. Polinder . Structural mass in direct-drive permanent magnet electrical generators. IET Renew. Power Gener. , 1 , 3 - 15
6. 6)
  - 19. Pinilla, M., Martinez, S.: ‘Optimal design of permanent-magnet direct-drive generator for wind energy considering the cost uncertainty in raw materials’, Renew. Energy, 2012, 41, pp. 267–276, ISSN 0960-1481 (doi: 10.1016/j.renene.2011.11.005).
7. 7)
  - 8. Sievert, T.: Product Pick of the Week - The E-126 Wind Turbine from Enercon. http://w3.windfair.net/wind-energy/news/9167-product-pick-of-the-week-the-e-126-wind-turbine-from-enercon. Windfair - All in Wind, 05/2011.
8. 8)
  - 6. ENERCON GmbH: ‘E-126/6 MW in Georgsfeld, East Frisia and Estinnes’ (Installing Giant Windmills, Belgium, 2008). http://www.enercon.de/p/downloads/WB-0408-en.pdf. WINDBLATT, Enercon Magazine for Wind Energy, Issue 04.
9. 9)
  - 5. Hinsch, C.: ‘Repowering holds enormous potential’ (Juwinews, 2010) (a monthly publication of juwi AG), The E-126 from Enercon, pp 5, www.juwinorthamerica.com/downloads.html, 09/2010.
10. 10)
  - 22. Pyrhönen, J., Jokinen, T., Hrabovcová, V.: ‘Design of rotating electrical machines’ (John Wiley & Sons, Ltd., Chichester, 2013, 2nd edn.), Textbook, ISBN: 978-1-118-58157-5.
11. 11)
  - R. Semken , M. Polikarpova , P. Roytta . Direct-drive permanent magnet generators for high-power wind turbines: benefits and limiting factors. Renew. Power Gener. , 1 , 1 - 8
12. 12)
  - H. Li , Z. Chen . Overview of different wind generator systems and their comparisons. IET Renew. Power Gener. , 123 - 138
13. 13)
  - 3. Shrestha, G., Polinder, H., Ferreira, J.A.: ‘Scaling laws for direct drive generators in wind turbines’. IEEE Int. Conf. on Electric Machines and DrivesIEMDC'09, 2009, pp. 797–803.
14. 14)
  - 9. Sethuraman, L., Venugopal, V., Zavvos, A., et al: ‘Structural integrity of a direct-drive generator for a floating wind turbine’, Renew. Energy, 2014, 63, pp. 597–616, ISSN 0960-1481 (doi: 10.1016/j.renene.2013.10.024).
15. 15)
  - 21. International Institute of Welding: ‘Recommendations for fatigue design of welded joints and components’. Prepared by Joint Working Group XIII-XV (Hobbacher A, Chairman) for the Int. Institute of Welding, December 2008.
16. 16)
  - E. Spooner , P. Gordon , J.R. Bumby . Lightweight ironless-stator PM generators for direct-drive wind turbines. IEE Proc. Electr. Power Appl. , 1 , 17 - 26
17. 17)
  - 25. Nutakor, C.: ‘Modal analysis and numerical modeling of the dynamic properties of layered sheet-steel structure’. Master's thesis, LUT Energy Systems, Lappeenranta University of Technology, Finland, 2014.
18. 18)
  - 24. Zhu, Z.Q., Ruangsinchaiwanich, S., Ishak, D., et al: ‘Analysis of cogging torque in brushless machines having nonuniformly distributed stator slots and stepped rotor magnets’, IEEE Trans. Magn., 2005, 41, (10), pp. 3910–3912 (doi: 10.1109/TMAG.2005.854968).
19. 19)
  - 20. Alexandrova, Y., Semken, R.S., Pyrhönen, J.: ‘Permanent magnet synchronous generator design solution for large direct-drive wind turbines’, Int. Rev. Electr. Eng. (IREE), 2014, 8, (6), pp. 1728–1737.
20. 20)
  - 15. Engstrom, S., Lindgren, S.: ‘Design of Newgen direct drive generator for demonstration in a 3.5 MW wind turbine’. European Wind Energy Conf. and Exhibition (EWEC), Milan, Italy, 2007.
21. 21)
  - 4. de Vries, E.: ‘Close up – the E126, Still the World‘s Biggest Turbine’ (Windpower Monthly Internet Publication, 2012), www.windpowermonthly.com/article/1138562.
22. 22)
  - 16. Shrestha, G., Polinder, H., Bang, D.J., et al: ‘Structural flexibility: a solution for weight reduction of large direct-drive wind-turbine generators’, IEEE Trans. Energy Convers., 2010, 25, (3), pp. 732–740 (doi: 10.1109/TEC.2010.2048713).
23. 23)
  - 17. Stander, J.N., Venter, G., Kamper, M.J.: ‘Review of direct-drive radial flux wind turbine generator mechanical design’, Wind Energy, 2012, 15, (3), pp. 459–472 (doi: 10.1002/we.484).
24. 24)
  - 23. Chapman, S.: ‘Electric machinery fundamentals’ (Tata McGraw-Hill Education, 2005, 4th edn.), p. 272, Textbook, ISBN 10: 0071151559.
25. 25)
  - 10. Grauers, A.: ‘Design of direct-driven permanent-magnet generators for wind turbines’. PhD thesis, School of Electrical and Computer Engineering, Chalmers University of Technology, 1996.

Login

Not registered yet?

Share

Tools

Login to add to favourites

Key

Lightweight stator structure for a large diameter direct-drive permanent magnet synchronous generator intended for wind turbines

References

Related content