http://iet.metastore.ingenta.com
1887

Lumped and distributed passive elements

Lumped and distributed passive elements

For access to this article, please select a purchase option:

Buy chapter PDF
$16.00
(plus tax if applicable)
Buy Knowledge Pack
10 chapters for $120.00
(plus taxes if applicable)

IET members benefit from discounts to all IET publications and free access to E&T Magazine. If you are an IET member, log in to your account and the discounts will automatically be applied.

Learn more about IET membership 

Recommend Title Publication to library

You must fill out fields marked with: *

Librarian details
Name:*
Email:*
Your details
Name:*
Email:*
Department:*
Why are you recommending this title?
Select reason:
 
 
 
 
 
RF and Microwave Module Level Design and Integration — Recommend this title to your library

Thank you

Your recommendation has been sent to your librarian.

Lumped and distributed elements as passive components are the constituting parts of almost any radio frequency and microwave circuit. In the section on lumped elements, resistors, capacitors and inductors are discussed. The Chapter goes on to look at distributed elements, design considerations, miniaturization, and quality factor.

Chapter Contents:

  • 2.1 Introduction
  • 2.2 Lumped elements
  • 2.2.1 Resistors
  • 2.2.1.1 Resistor modeling
  • 2.2.1.2 Resistor implementation
  • 2.2.1.3 Attenuators
  • 2.2.2 Capacitors
  • 2.2.2.1 Capacitor modeling
  • 2.2.2.2 Capacitor implementation
  • 2.2.2.3 Electrostatic discharge in capacitors
  • 2.2.2.4 On-module electrostatic discharge protection
  • 2.2.3 Inductors
  • 2.2.3.1 Inductor modeling
  • 2.2.3.2 Inductor implementation
  • 2.2.3.3 Mutual inductance
  • 2.2.3.4 Via holes
  • 2.2.3.5 Crossovers and airbridges
  • 2.3 Distributed elements
  • 2.4 Design considerations
  • 2.4.1 Self-resonant frequency
  • 2.4.2 Reactance slope
  • 2.4.3 Inductor orientation
  • 2.5 Miniaturization of distributed elements
  • 2.5.1 High permittivity materials
  • 2.5.2 Capacitively loaded transmission line
  • 2.6 Quality factor calculation
  • 2.6.1 Q-factor improvement methods of inductors
  • 2.6.1.1 Layout optimization
  • 2.6.1.2 Patterned ground shield
  • 2.6.1.3 Thick metal
  • 2.6.1.4 Substrate modification
  • 2.6.1.5 Magnetic material coating
  • 2.6.1.6 Differential excitation
  • References

Inspec keywords: microwave integrated circuits; resistors; lumped parameter networks; inductors; capacitors; Q-factor; distributed parameter networks

Other keywords: distributed passive elements; elements Miniaturization; quality factor calculation; lumped passive elements; resistor; design considerations; inductor; capacitor

Subjects: Inductors and transformers; Resistors; Microwave integrated circuits; Lumped linear networks; Capacitors; Distributed linear networks

Preview this chapter:
Zoom in
Zoomout

Lumped and distributed passive elements, Page 1 of 2

| /docserver/preview/fulltext/books/cs/pbcs034e/PBCS034E_ch2-1.gif /docserver/preview/fulltext/books/cs/pbcs034e/PBCS034E_ch2-2.gif

Related content

content/books/10.1049/pbcs034e_ch2
pub_keyword,iet_inspecKeyword,pub_concept
6
6
Loading
This is a required field
Please enter a valid email address