Low-cost parametric test and diagnosis of RF systems using multi-tone response envelope detection

Low-cost parametric test and diagnosis of RF systems using multi-tone response envelope detection

For access to this article, please select a purchase option:

Buy article PDF
(plus tax if applicable)
Buy Knowledge Pack
10 articles for £75.00
(plus taxes if applicable)

IET members benefit from discounts to all IET publications and free access to E&T Magazine. If you are an IET member, log in to your account and the discounts will automatically be applied.

Learn more about IET membership 

Recommend Title Publication to library

You must fill out fields marked with: *

Librarian details
Your details
Why are you recommending this title?
Select reason:
IET Computers & Digital Techniques — Recommend this title to your library

Thank you

Your recommendation has been sent to your librarian.

Because of aggressive technology scaling and multi-GHz operating frequencies of radio frequency (RF) devices, parametric failure test and diagnosis of RF circuitry is becoming increasingly important for the reduction of production test cost and faster yield ramp-up. A low-cost test and diagnosis method is proposed for multi-parametric faults in wireless systems that allows for the accurate prediction of the end-to-end specifications as well as the specifications of all the embedded RF modules. The procedure is based on application of an optimised test stimulus and extraction of its transient test response envelopes at RF signal nodes using a simple diode-based envelope detector. The test response is down-converted to lower frequencies compared to the operating frequency, thus eliminating the need to make RF measurements using expensive instrumentation. The specifications as well as the diagnostic information are computed from the test response of the envelope detector using statistical models. It is shown that the resulting information (features) in the transient envelope can accurately predict a host of test specifications using a single test configuration and test response capture event. Hardware measurement data from a 1.575 GHz transceiver shows that the test specifications of the system as well as the modules can be predicted with a high degree of accuracy using this method.


    1. 1)
      • Prediction of analog performance parameters using fast transient testing
    2. 2)
      • Fault diagnosis of analog circuits
    3. 3)
      • Somayajula, S.S., Sanchez-Sinencio, E., Pineda de Gyvez, J.: `A power supply ramping and current measurement based technique for analog fault diagnosis', Proc. VLSI Test Symp., April 1994, p. 234–239
    4. 4)
      • Cherubal, S., Chatterjee, A.: `Parametric fault diagnosis for analog systems using functional mapping', Proc. Design, Automation and Test in Europe Conf. and Exhibition, March 1999, p. 195–200
    5. 5)
      • A new diagnosis approach for handling tolerance in analog and mixed-signal circuits by using fuzzy math
    6. 6)
      • Automated selection of test frequencies for fault diagnosis in analog electronic circuits
    7. 7)
      • A low-cost test solution for wireless phone RFICs
    8. 8)
      • Voorakaranam, R., Cherubal, S., Chatterjee, A.: `A signature test framework for rapid production testing of RF circuits', Proc. Design Automation and Test in Europe Conf. and Exhibition, March 2002, p. 186–191
    9. 9)
      • Acar, E., Ozev, S.: `Defect-based RF testing using a new catastrophic fault model', IEEE Int. Test Conf., Nov 2005, paper 17.3
    10. 10)
      • Acar, E., Ozev, S.: `Diagnosis of the failing components in RF receivers through adaptive full-path measurements', Proc. VLSI Test Symp., May 2005, p. 374–379
    11. 11)
      • An architecture for self-test of a wireless communication system using sampled IQ modulation and boundary scan
    12. 12)
      • Halder, A., Bhattacharya, S., Srinivasan, G., Chatterjee, A.: `A system-level alternate test approach for specification test of RF transceivers in loopback mode', Proc. Int. Conf., VLSI Design, Jan. 2005, p. 289–294
    13. 13)
      • A translinear RMS detector for embedded test of RF ICs
    14. 14)
      • A new low-cost RF built-in self-test measurement for system-on-chip transceivers
    15. 15)
      • Gopalan, A., Das, T., Washburn, C., Mukund, P.R.: `An ultra-fast, on-chip BiST for RF low noise amplifiers', Proc. Int. Conf., VLSI Design, Jan. 2005, p. 485–490
    16. 16)
      • Valdes-Garcia, A., Venkatasubramanian, R., Srinivasan, R., Silva-Martinez, J., Sanchez-Sinencio, E.: `A CMOS RF RMS detector for built-in testing of wireless transceivers', Proc. VLSI Test Symp., May 2005, p. 249–254
    17. 17)
      • Akbay, S.S., Chatterjee, A.: `Built-in test of RF components using mapped feature extraction sensors', Proc. VLSI Test Symp., May 2005, p. 243–248
    18. 18)
      • Bhattacharya, S., Chatterjee, A.: `Use of embedded sensors for built-in-test of RF circuits', Proc. Int. Test Conf., 2004, p. 801–809
    19. 19)
      • Kulhalli, S., Seth, S., Fu, S.: `An integrated linear RF power detector', Proc. ISCAS, 2004, p. I.625–I.628
    20. 20)
      • Envelope and pre-envelopes of real waveforms
    21. 21)
      • Introduction to RF simulation and its application
    22. 22)
      • Halder, A., Bhattacharya, S., Chatterjee, A.: `Automatic multitone alternate test generation for RF circuits using behavioural models', Proc. Int. Test Conf., Sept. 2003, p. 665–673
    23. 23)
      • Optimised wafer-probe and assembled package test design for analog circuits
    24. 24)
      • Multivariate adaptive regression splines
    25. 25)
      • Embedded loopback test for RF ICs

Related content

This is a required field
Please enter a valid email address