Efficient self-powered convertor with digitally controlled oscillator-based adaptive maximum power point tracking and RF kick-start for ultralow-voltage thermoelectric energy harvesting

Chuang Wang; Zunchao Li; Kai Zhao; Qiang Guo

Efficient self-powered convertor with digitally controlled oscillator-based adaptive maximum power point tracking and RF kick-start for ultralow-voltage thermoelectric energy harvesting

View Fulltext

Author(s): Chuang Wang ¹ ; Zunchao Li ¹ ; Kai Zhao ¹ ; Qiang Guo ²
- Affiliations: 1: Department of Microelectronics, Xi'an Jiaotong University, Xi'an, Shaanxi 710049, People's Republic of China ;
  2: State Key Lab of ASIC&Syst., Fudan University, Shanghai 201203, People's Republic of China
Source: Volume 10, Issue 2, March 2016, p. 147 – 155
DOI: 10.1049/iet-cds.2015.0058 , Print ISSN 1751-858X, Online ISSN 1751-8598

Received 06/02/2015, Accepted 23/09/2015, Revised 17/09/2015, Published 01/03/2016

A self-powered convertor for thermoelectric energy harvesting in body sensor nodes (BSNs) is designed to boost extremely low voltage to the typical supply voltage of BSNs. An adaptive maximum power point tracking (MPPT) based on digitally controlled oscillator (DCO) is achieved by adjusting the switching frequency according to the relation between the half open-circuit voltage of thermoelectric generator and the equivalent voltage. DCO exhibits small line sensitivity and temperature coefficient (TC). Radio frequency (RF) kick-start based on a self-synchronous rectifier is introduced to achieve the no-battery effect. A modified zero current switching based on the common-gate comparator is utilised to decrease the power dissipation of power metal–oxide–semiconductor field-effect transistors. In addition, the power dissipation of the main blocks is reduced by discontinuing the clocked and common-gate comparators after comparison in each cycle, and by making most transistors of DCO and the complementary metal-oxide-semiconductor (CMOS) voltage reference work in the weak inversion or linear region. The zero TC principle of the CMOS voltage reference is extended to all process. The novel convertor is designed and verified in Central Semiconductor Manufacturing Corporation CMOS 0.18 µm process. The results reveal that it achieves adaptive MPPT without battery and exhibits a peak end-to-end efficiency of about 63%.

References

1. 1)
  - 23. Ueno, K., Hirose, T., Asai, T., et al: ‘A 300 nW, 15 ppm/°C, 20 ppm/V CMOS voltage reference circuit consisting of subthreshold MOSFETs’, IEEE J. Solid-State Circuits, 2009, 44, (7), pp. 2047–2054 (doi: 10.1109/JSSC.2009.2021922).
2. 2)
  - 16. Bassi, G., Colalongo, L., Richelli, A., et al: ‘A 150 mV–1.2 V fully-integrated DC-DC converter for thermal energy harvesting’. Int. Symp. on Power Electronics, Electrical Drives, Automation and Motion, Sorrento, Italy, June 2012, pp. 331–334.
3. 3)
  - 2. ‘ITRS2013–ESH_Summary’, http://www.itrs.net/Links/2013ITRS/Home2013.htm, accessed January 2015.
4. 4)
  - 5. Richelli, A., Comensoli, S., Kovacs-Vajna, Z.M.: ‘A DC/DC boosting technique and power management for ultralow-voltage energy harvesting applications’, IEEE Trans. Ind. Electron., 2012, 59, (6), pp. 2701–2708 (doi: 10.1109/TIE.2011.2167890).
5. 5)
  - 12. Yuk, Y.S., Jung, S., Gwon, H.D.: ‘An energy pile-up resonance circuit extracting maximum 422% energy from piezoelectric material in a dual-source energy-harvesting interface’. Proc. IEEE Int. Solid-State Circuits Conf. Digest of Technical Papers, San Francisco, USA, February 2014, pp. 402–403.
6. 6)
  - 22. Abu Qahouq, J.A.: ‘Control scheme for sensorless operation and detection of CCM and DCM operation modes in synchronous switching power converters’, IEEE Trans. Power Electron., 2010, 25, (10), pp. 2489–2495 (doi: 10.1109/TPEL.2010.2049375).
7. 7)
  - 6. Carlson, E.J., Strunz, K., Otis, B.P.: ‘A 20 mV input boost converter with efficient digital control for thermoelectric energy harvesting’, IEEE J. Solid-State Circuits, 2010, 45, (4), pp. 741–750 (doi: 10.1109/JSSC.2010.2042251).
8. 8)
  - 26. Razavi, B., Wooley, B.A.: ‘Design techniques for high-speed, high-resolution comparators’, IEEE J. Solid-State Circuits, 1992, 27, (13), pp. 1916–1926 (doi: 10.1109/4.173122).
9. 9)
  - 14. Azevedo, J.A.R., Santos, F.E.S.: ‘Energy harvesting from wind and water for autonomous wireless sensor nodes’, IET Circuits Devices Syst., 2012, 6, (6), pp. 413–420 (doi: 10.1049/iet-cds.2011.0287).
10. 10)
  - 29. Denier, U.: ‘Analysis and design of an ultralow-power CMOS relaxation oscillator’, IEEE Trans. Circuits Syst. I, Regul. Pap., 2010, 57, (8), pp. 1973–1982 (doi: 10.1109/TCSI.2010.2041504).
11. 11)
  - 4. Chen, H.C., Lin, W.J.: ‘MPPT and voltage balancing control with sensing only inductor current for photovoltaic-fed, three-level, boost-type converters’, IEEE Trans. Power Electron., 2014, 29, (1), pp. 29–35 (doi: 10.1109/TPEL.2013.2262056).
12. 12)
  - 13. Jia, C., Chen, H., Liu, M., et al: ‘Integrated power management circuit for piezoelectric generator in wireless monitoring system of orthopaedic implants’, IET Circuits Devices Syst., 2008, 2, (6), pp. 485–494 (doi: 10.1049/iet-cds:20070342).
13. 13)
  - 28. Sadeghi, N., Sharif-Bakhtiar, A., Mirabbasi, S.: ‘A 0.007-mm2 108 p±/°C 1-MHz relaxation oscillator for high-temperature applications up to 180°C in 0.13 µm CMOS’, IEEE Trans. Circuits Syst. I, Regul. Pap., 2013, 60, (7), pp. 1692–1701 (doi: 10.1109/TCSI.2012.2226500).
14. 14)
  - 15. Porcarelli, D., Spenza, D., Brunelli, D., et al: ‘Adaptive rectifier driven by power intake predictors for wind energy harvesting sensor networks’, IEEE J. Emerg. Sel. Top. Power Electron., 2015, 3, (2), pp. 471–482 (doi: 10.1109/JESTPE.2014.2316527).
15. 15)
  - 6. Bandyopadhyay, S., Chandrakasan, A.P.: ‘Platform architecture for solar, thermal, and vibration energy combining with MPPT and single inductor’, IEEE J. Solid-State Circuits, 2012, 47, (9), pp. 2199–2215 (doi: 10.1109/JSSC.2012.2197239).
16. 16)
  - 7. Ramadass, Y.K., Chandrakasan, A.P.: ‘A batteryless thermoelectric energy-harvesting interface circuit with 35 mV startup voltage’, IEEE J. Solid-State Circuits, 2011, 46, (1), pp. 333–341 (doi: 10.1109/JSSC.2010.2074090).
17. 17)
  - 30. Weng, P.S., Tang, H.Y., Ku, P.C., et al: ‘50 mV-input batteryless boost converter for thermal energy harvesting’, IEEE J. Solid-State Circuits, 2013, 48, (4), pp. 1031–1041 (doi: 10.1109/JSSC.2013.2237998).
18. 18)
  - 3. Uprety, S., Lee, H.: ‘A 43 V 400 mW-to-21 W global-search-based photovoltaic energy harvester with 350 µs transient time, 99.9% MPPT efficiency, and 94% power efficiency’. Proc. IEEE Int. Solid-State Circuits Conf. Digest of Technical Papers, San Francisco, USA, February 2014, pp. 404–405.
19. 19)
  - 27. Rahman, L.F., Reaz, M.B.I., Yin, C.C.: ‘Design of high speed and low offset dynamic latch comparator in 0.18 µm CMOS process’, PLOS ONE, 2014, 9, (10), pp. e108634:1–e108634:12 (doi: 10.1371/journal.pone.0108634).
20. 20)
  - 32. Leung, K.N., Mok, P.K.T.: ‘A sub-1-V 15-ppm/°C CMOS bandgap voltage reference without requiring low threshold voltage device’, IEEE J. Solid-State Circuits, 2002, 37, (4), pp. 526–530 (doi: 10.1109/4.991391).
21. 21)
  - 24. Zhang, Y.Q., Zhang, F., Shakhsheer, Y., et al: ‘A batteryless 19 µW MICS/ISM-band energy harvesting body sensor node soc for EXG applications’, IEEE J. Solid-State Circuits, 2013, 48, (1), pp. 199–213 (doi: 10.1109/JSSC.2012.2221217).
22. 22)
  - 21. De Vita, G., Marraccini, F., Iannaccone, G.: ‘Low-voltage low-power CMOS oscillator with low temperature and process sensitivity’. IEEE Int. Symp. on Circuits and Systems, New Orleans, USA, 2007, pp. 2152–2155.
23. 23)
  - 17. Chen, P., Ishida, K., Ikeuchi, K., et al: ‘Startup techniques for 95 mV step-up converter by capacitor pass-on scheme and Vth-tuned oscillator with fixed charge programming’, IEEE J. Solid-State Circuits, 2012, 47, (5), pp. 1252–1260 (doi: 10.1109/JSSC.2012.2185589).
24. 24)
  - 35. Luo, H., Han, Y., Cheung, R.C.C., et al: ‘Subthreshold CMOS voltage reference circuit with body bias compensation for process variation’, IET Circuits Devices Syst., 2012, 6, (3), pp. 198–203 (doi: 10.1049/iet-cds.2011.0170).
25. 25)
  - 11. Shim, M., Kim, J., Jung, J., et al: ‘Self-powered 30 µW-to-10 mW piezoelectric energy-harvesting system with 9.09 ms/V maximum power point tracking time’. Proc. IEEE Int. Solid-State Circuits Conf. Digest of Technical Papers, San Francisco, USA, February 2014, pp. 406–407.
26. 26)
  - 8. Im, J.P., Wang, S.W., Lee, K.H., et al: ‘A 40 mV transformer-reuse self-startup boost converter with MPPT control for thermoelectric energy harvesting’. Proc. IEEE Int. Solid-State Circuits Conf. Digest of Technical Papers, San Francisco, USA, February 2012, pp. 104–106.
27. 27)
  - 1. Verma, N., Shoeb, A., Bohorquez, J., et al: ‘A micro-power EEG acquisition SoC with integrated feature extraction processor for a chronic seizure detection system’, IEEE J. Solid-State Circuits, 2010, 45, (4), pp. 804–816 (doi: 10.1109/JSSC.2010.2042245).
28. 28)
  - 13. Bassi, G., Colalongo, L., Richelli, A., et al: ‘100 mV–1.2 V fully-integrated DC–DC converters for thermal energy harvesting’, IET Power Electron., 2013, 6, (6), pp. 1151–1156 (doi: 10.1049/iet-pel.2012.0625).
29. 29)
  - 31. Wang, A., Clhoun, B.H., Chandrakasan, A.P.: ‘Sub-threshold design for ultralow-power systems’ (Springer, 2006).
30. 30)
  - 34. Yang, B.D.: ‘250-mV supply subthreshold CMOS voltage reference using a low-voltage comparator and a charge-pump circuit’, IEEE Trans. Circuits Syst. II, Express Briefs, 2014, 61, (11), pp. 850–854 (doi: 10.1109/TCSII.2014.2350354).
31. 31)
  - 25. Carreon-Bautista, S., Eladawy, A., Mohieldin, A.N., et al: ‘Boost converter with dynamic input impedance matching for energy harvesting with multi-array thermoelectric generators’, IEEE Trans. Ind. Electron., 2014, 61, (10), pp. 5345–5353 (doi: 10.1109/TIE.2014.2300035).
32. 32)
  - 20. Kim, J., Kim, C.: ‘A DC–DC boost converter with variation-tolerant MPPT technique and efficient ZCS circuit for thermoelectric energy harvesting applications’, IEEE Trans. Power Electron., 2013, 28, (8), pp. 3827–3833 (doi: 10.1109/TPEL.2012.2231098).
33. 33)
  - 33. Ng, D.C.W., Kwong, D.K.K., Wong, N.: ‘A sub-1 V, 26 µW, low-output-impedance CMOS bandgap reference with a low dropout or source follower mode’, IEEE Trans. Very Large Scale Integr. Syst., 2011, 19, (7), pp. 1305–1309 (doi: 10.1109/TVLSI.2010.2046658).
34. 34)
  - 19. Montecucco, A., Siviter, J., Knox, A.R., et al: ‘Simple, fast and accurate maximum power point tracking converter for thermoelectric generators’. IEEE Energy Conversion Congress and Exposition, Raleigh, USA, September 2012, pp. 2777–2783.
35. 35)
  - 9. Richelli, A., Colalongo, L., Tonoli, S., et al: ‘A 0.2–1.2 V DC/DC boost converter for power harvesting applications’, IEEE Trans. Power Electron., 2009, 24, (6), pp. 1541–1546 (doi: 10.1109/TPEL.2009.2013224).

Login

Not registered yet?

Share

Tools

Login to add to favourites

Key

Efficient self-powered convertor with digitally controlled oscillator-based adaptive maximum power point tracking and RF kick-start for ultralow-voltage thermoelectric energy harvesting

References

Related content